Solid Router Bits

This 57-200 series spiral downcut routing end mill is made of high-performance solid carbide with a bright finish. It measures one-inch cut length, ¼-inch shank diameter, ¼-inch cutter diameter, 2½-inch overall length, two flutes, and 30 degree helix angle. The right-hand end mill has center cutting and a fractional inch measurement system.

This 57-200 series spiral downcut routing end mill is made of high-performance solid carbide with a bright finish. It measures one-inch cut length, ¼-inch shank diameter, ¼-inch cutter diameter, 2½-inch overall length, two flutes, and 30 degree helix angle. The right-hand end mill has center cutting and a fractional inch measurement system.

This 63-600 series spiral O-flute upcut routing end mill is made of high-performance solid carbide with a bright finish. It measures ¾-inch cut length, ¼-inch shank diameter, ¼-inch cutter diameter, 2½-inch overall length, and 22 degree helix angle. The right-hand single-routing end mill has center cutting and a fractional inch measurement system.

This 63-600 series spiral O-flute upcut routing end mill is made of high-performance solid carbide with a bright finish. It measures ¾-inch cut length, ¼-inch shank diameter, ¼-inch cutter diameter, 2½-inch overall length, and 22 degree helix angle. The right-hand single-routing end mill has center cutting and a fractional inch measurement system.

This 52-600 series spiral O-flute upcut routing end mill is made of high-performance solid carbide with a bright finish. It measures one-inch cut length, ⅜-inch shank diameter, ⅜-inch cutter diameter, three-inch overall length, two flutes, and 11 degree helix angle. The right-hand end mill has center cutting and a fractional inch measurement system.

This 52-600 series spiral O-flute upcut routing end mill is made of high-performance solid carbide with a bright finish. It measures one-inch cut length, ⅜-inch shank diameter, ⅜-inch cutter diameter, three-inch overall length, two flutes, and 11 degree helix angle. The right-hand end mill has center cutting and a fractional inch measurement system.

This router bit with a diamond cut is made of a solid carbide with a bright finish. It measures a ¼-inch shank diameter, a ¾-inch cut length, and 2½-inch overall length. The router bit has a center-end mill cutting and right-hand cutting direction. It is for use with plastic/composite material and end mill finishing.

This router bit with a diamond cut is made of a solid carbide with a bright finish. It measures a ¼-inch shank diameter, a ¾-inch cut length, and 2½-inch overall length. The router bit has a center-end mill cutting and right-hand cutting direction. It is for use with plastic/composite material and end mill finishing.

This solid router bit with a diamond cut is made of carbide. It measures a ½-inch shank diameter, one-inch cut length, three-inch overall length, and a maximum speed ranging from 15000 to 40000 RPM. The router bit has center-end mill cutting and right-hand cutting direction. It is for use with composite material.

This solid router bit with a diamond cut is made of carbide. It measures a ½-inch shank diameter, one-inch cut length, three-inch overall length, and a maximum speed ranging from 15000 to 40000 RPM. The router bit has center-end mill cutting and right-hand cutting direction. It is for use with composite material.

This 52-550 series spiral upcut routing end mill is made of high-performance solid carbide with a bright finish. It measures 2¼-inch cut length, ¼-inch shank diameter, four-inch overall length, two flutes, and 25 degree helix angle. The right-hand single-routing end mill has center cutting and a fractional inch measurement system.

This 52-550 series spiral upcut routing end mill is made of high-performance solid carbide with a bright finish. It measures 2¼-inch cut length, ¼-inch shank diameter, four-inch overall length, two flutes, and 25 degree helix angle. The right-hand single-routing end mill has center cutting and a fractional inch measurement system.

This 190 series cyber router measures one-inch flute length, ¼-inch shank diameter, ¼-inch head diameter, and three-inch overall length. It is for use with graphite, glass, and carbon fibre.

This 190 series cyber router measures one-inch flute length, ¼-inch shank diameter, ¼-inch head diameter, and three-inch overall length. It is for use with graphite, glass, and carbon fibre.

This 60-100MW series compression spiral routing end mill is made of high-performance solid carbide with a bright finish. It measures 1⅛-inch cut length, ½-inch shank diameter, ½-inch cutter diameter, three-inch overall length, two flutes, and 30 degree helix angle. The right-hand end mill has center cutting and a fractional inch measurement system.

This 60-100MW series compression spiral routing end mill is made of high-performance solid carbide with a bright finish. It measures 1⅛-inch cut length, ½-inch shank diameter, ½-inch cutter diameter, three-inch overall length, two flutes, and 30 degree helix angle. The right-hand end mill has center cutting and a fractional inch measurement system.

This 56-000 series straight O-flute routing end mill is made of high-performance solid carbide with a bright finish. It measures ½-inch cut length, ¼-inch shank diameter, ⅛-inch cutter diameter, two-inch overall length, two flutes, and zero degree helix angle. The right-hand end mill has center cutting and a fractional inch measurement system.

This 56-000 series straight O-flute routing end mill is made of high-performance solid carbide with a bright finish. It measures ½-inch cut length, ¼-inch shank diameter, ⅛-inch cutter diameter, two-inch overall length, two flutes, and zero degree helix angle. The right-hand end mill has center cutting and a fractional inch measurement system.

This 63-600 series spiral O-flute upcut routing end mill is made of high-performance solid carbide with a bright finish. It measures ⅝-inch cut length, ¼-inch shank diameter, 3/16-inch cutter diameter, two-inch overall length, and 22 degree helix angle. The right-hand single-routing end mill has center cutting and a fractional inch measurement system.

This 63-600 series spiral O-flute upcut routing end mill is made of high-performance solid carbide with a bright finish. It measures ⅝-inch cut length, ¼-inch shank diameter, 3/16-inch cutter diameter, two-inch overall length, and 22 degree helix angle. The right-hand single-routing end mill has center cutting and a fractional inch measurement system.

This routing end mill spiral O-flute downcut bit is made of solid carbide with a bright finish. It measures a ¼-inch shank diameter, a 9/16-inch cut length, two-inch overall length, and a 21 degree helix angle. The router bit has square center-end mill cutting and right-hand cutting direction. It is for use with composite and end mill finishing.

This routing end mill spiral O-flute downcut bit is made of solid carbide with a bright finish. It measures a ¼-inch shank diameter, a 9/16-inch cut length, two-inch overall length, and a 21 degree helix angle. The router bit has square center-end mill cutting and right-hand cutting direction. It is for use with composite and end mill finishing.

This 63-750 series spiral O-flute upcut routing end mill is made of high-performance solid carbide with a bright finish. It measures ¾-inch cut length, ¼-inch shank diameter, ¼-inch cutter diameter, 2½-inch overall length, and 21 degree helix angle. The right-hand single-routing end mill has center cutting and a fractional inch measurement system.

This 63-750 series spiral O-flute upcut routing end mill is made of high-performance solid carbide with a bright finish. It measures ¾-inch cut length, ¼-inch shank diameter, ¼-inch cutter diameter, 2½-inch overall length, and 21 degree helix angle. The right-hand single-routing end mill has center cutting and a fractional inch measurement system.

This 52-200 series spiral upcut routing end mill is made of high-performance solid carbide with a bright finish. It measures one-inch cut length, ¼-inch shank diameter, 3/16-inch cutter diameter, 2½-inch overall length, two flutes, and 30 degree helix angle. The right-hand end mill has center cutting and a fractional inch measurement system.

This 52-200 series spiral upcut routing end mill is made of high-performance solid carbide with a bright finish. It measures one-inch cut length, ¼-inch shank diameter, 3/16-inch cutter diameter, 2½-inch overall length, two flutes, and 30 degree helix angle. The right-hand end mill has center cutting and a fractional inch measurement system.

This 63-750 series spiral O-flute upcut routing end mill is made of high-performance solid carbide with a bright finish. It measures 1¼ inches cut length, ¼-inch shank diameter, ¼-inch cutter diameter, three-inch overall length, and 21 degree helix angle. The right-hand end mill has center cutting and a fractional inch measurement system.

This 63-750 series spiral O-flute upcut routing end mill is made of high-performance solid carbide with a bright finish. It measures 1¼ inches cut length, ¼-inch shank diameter, ¼-inch cutter diameter, three-inch overall length, and 21 degree helix angle. The right-hand end mill has center cutting and a fractional inch measurement system.

This 63-500 series spiral O-flute upcut routing end mill is made of high-performance solid carbide with a bright finish. It measures ½-inch cut length, ¼-inch shank diameter, ⅛-inch cutter diameter, two-inch overall length, and 24 degree helix angle. The right-hand single-routing end mill has center cutting and a fractional inch measurement system.

This 63-500 series spiral O-flute upcut routing end mill is made of high-performance solid carbide with a bright finish. It measures ½-inch cut length, ¼-inch shank diameter, ⅛-inch cutter diameter, two-inch overall length, and 24 degree helix angle. The right-hand single-routing end mill has center cutting and a fractional inch measurement system.

This 190 series solid router bit with a double diamond cut is made of carbide. It measures ¼-inch shank diameter, ¾ inch flute length, 2½-inch overall length, and a maximum speed of 10000 RPM. The single-end router bit is for use with composite material and fibreglass routing.

This 190 series solid router bit with a double diamond cut is made of carbide. It measures ¼-inch shank diameter, ¾ inch flute length, 2½-inch overall length, and a maximum speed of 10000 RPM. The single-end router bit is for use with composite material and fibreglass routing.