Filter Results By

Brand
Shop By

Motors

http://catalogue.acklandsgrainger.com/2017?hybris=true

2283 Results Found

Results per page :  16 | 32 | 48
  • Available only while supplies last. Quantities may be limited.
  • IDEAL
  • BRUSH SEATER SOFT 2X1X4-3/4
  • Item # IDI23-036S
  • Mfr. Model # 23-036S
  • Gentle-acting abrasive is very gentle for seating carbon brushes and cleaning commutators and slip rings. Made of soft, loosely bound grain that produces a scouring effect as it is held against the commutator. The abrasive wears away sufficiently for self-cleaning, but does not remove or scratch the copper. Often called a "chalk" stone because of its chalk-like colour and texture.

    View more View less
  • CATALOGUE PAGE # 1507
  • DAYTON
  • CONTROL SPEED 1/50-1/6HP
  • Item # DTN4Z827
  • Mfr. Model # 4Z827
  • DC speed controls for 90 volt and 180 volt motor and gearmotor, IR comp. fixed, HP range 1/50-1/6, speed regulation % nameplate RPM 10-30, chassis enclosure, height 4 inches, width 4 inches, depth 2 inches.

    View more View less
    CATALOGUE PAGE # 1508
  • DAYTON
  • MOTOR 1/4 HP 60HZ BELT
  • Item # GGE3K771
  • Mfr. Model # 3K771
  • Split-phase, open drip-proof, residential duty. Sleeve bearing. Full load amps 5.0. HP 1/4. Insulation class B. Nameplate RPM 1,725. NEMA frame 48Y. Service factor 1.35. Shaft dimension 1/2 inch diameter x 1-1/2 inches long. Volts 60 Hz 115.

    View more View less
    CATALOGUE PAGE # 1500
  • DART CONTROLS
  • GENERATOR 4-24VDC 10 PULSE/REV
  • Item # WWG5JJ65
  • Mfr. Model # 5JJ65
  • Pulse Generator, Provides Current Sinking Square-wave Pulses with Frequency Proportional to Shaft RPM of Unit to Which It is Mounted, Pick-up Mounts with a #10-32 Screw Directly to Motor Shaft Being Monitored, 10 Pulses per Revolution, Input Voltage 4.5 to 24VDC, Max. RPM 5000, Output Cable Length (Ft.) 6, 3 Wire 18 AWG, Ball Bearings, Operating Temp. -10 to 45 Degree C, Molded Santoprene Rubber Housing

    View more View less
    CATALOGUE PAGE # 1508
  • DAYTON
  • C-FRAME MOTOR,1/150 HP,2750RPM,120
  • Item # AOS4M180D
  • Mfr. Model # 4M180D
  • C-frame motor. Shaded pole. Open air-over. 1/150 HP. Nameplate RPM 2750. NEMA/IEC frame non-standard. Voltage 120, 60 Hz, 1 Phase. Full load amps 0.52. Stud mounting. One shot thermal protection. Insulation class B. Service factor 1.0. Bronze sleeve beari

    View more View less
    CATALOGUE PAGE # 1504
  • DAYTON
  • CAPACITOR 7.5MFD 370V
  • Item # DMD2MDV6
  • Mfr. Model # 2MDV6
  • Motor run capacitor, EIA UL Base A, 1/4 inch male terminals, temperature range -40 to 69 degrees C.

    View more View less
    CATALOGUE PAGE # 1507
  • DAYTON
  • MOTOR 1/2 HP YOKE
  • Item # GGE6K809
  • Mfr. Model # 6K809
  • Split-phase, yoke-type welded tab. Body diameter 5-5/8 inches. Enclosure TEAO. Full load amps 6.4. HP 1/2. Insulation class B. Length 10-1/8 inches. Nameplate RPM 1,725. No. of speeds 1. Rotation facing shaft end CW/CCW. Shaft dimensions 5/8 inch diameter x 2 inch length. Volts 60 Hz 115.

    View more View less
    CATALOGUE PAGE # 1500
  • DAYTON
  • MOTOR 1/3 HP 60HZ BELT
  • Item # GGE6K778
  • Mfr. Model # 6K778
  • Split-phase, open drip-proof, residential duty. Sleeve bearing. Full load amps 6.6. HP 1/3. Insulation class B. Nameplate RPM 1,725. NEMA frame 48Y. Service factor 1.35. Shaft dimension 1/2 inch diameter x 1-1/2 inches long. Volts 60 Hz 115.

    View more View less
    CATALOGUE PAGE # 1500
Results per page :  16 | 32 | 48

Add to Order List

Your items were added

Your items were added to some lists

Max quantity exceeded. The item could not be added to the following List(s)

No Existing List Found. Please Create New List below.

Your list has been created

Please select a list